Nowadays it seems like everyone has a different way to do a bench press, and everyone seems to have the best way to do a bench press to work your chest. But it also seems everyone’s is completely different.
Do you flap your shoulders out all the way? Do you put them to your sides? How far do you grip the bar? How far do you go down, 1cm above the chest, do you touch your chest? How far do you go up, do I lock my elbows or do I not. Can I arch my back, is it good to arch my back? What about my chest, do I stick that out?
Even the professionals all seem to have a different perspective on it, one may say lock it gives you the full range of motion others may say don’t lock especially with heavyweights because you are more prone to injury. Back to the point, I want to clear the air with this one.
How about Hand and Arm Positioning. Your arms must first of all be in a natural relaxed state to maximize the use of the chest and to make the lifting easier so you are actually using your full potential.
If you are not in that natural position and there is a strain on your joints and more engagement of weaker muscles you ultimately will have a harder time lifting because you are not lifting efficiently as well as the fact that work is taken off of the chest and distributed more to other supporting muscles.
Think of it like a pushing a wall only with your knuckles instead of your palms. If you can close your eyes and picture this you can do the same thing on the bench to help get the positioning right.
The positioning hand wise is not where the strips are on the bar, in fact, some older bars don’t even have those, the positioning is wherever your hands end up so that by the end of the lift you have your hands above the outermost part of the chest.
This will not look like your arms are positioned shoulder-width this will usually be slightly wider where you almost look like your pushing up and away from the body. Now, this next part is important, your shoulders can make your arms flap out so they make a straight line or they can be pressed against the body, you want them 45 degrees right in between both of those. This way you don’t put too much stress on the shoulders and you engage as much of the chest as possible.
Must Read: How Does Multivitamin Help For BodyBuilding?
So now how about locking?
With lightweight where you can push out 15 or more feel free to lock. However, when you start getting stronger or strength training with heavier weight do not lock. The first reason is that you don’t want to put that much weight on your elbow joints, it can lead to injury.
But let’s pretend you don’t care about that and you feel you know how to lift and you lift safe, by not locking you’re giving yourself a strength gaining the benefit of keeping the muscle engaged for longer and is actually highly recommended to build muscle which can be done with any exercise.
How far are you supposed to go down?
The answer to this is not specific because we are all different and also have differently worked chests, some bigger some smaller. Saying to go 1 inch away from the chest is ideal is like saying curling 25-pound dumbbells are ideal. It just doesn’t apply to everyone the same.
Realistically you want to go as far down as it takes to get your arms going 90 degrees. If you drop your arms past that point you are only stretching your chest and tensing your back. Keep in mind you are not working the back simply because you are lying upright with your chest to the air and back to the ground meaning your chest is not resisting any weight and there is no gravity acting on it so it is not being worked. 90 degrees is as far as you need to go, past that is pointless.
What about your back, particularly the lower back, is it OK to arch this to push up the weight.
What if I stick my chest out then can I arch it? The answer is no to both of these, it is never OK to arch your back even with your chest stuck out. Arching your back is nothing more than bad form and in doing this you take the weight off of what your chest has to lift.
This is not good because you cheat your chest of work and ultimately the stimulation to grow. Every time you can’t lift the weight presented you arch the back to assist with the rest, meaning you’re never really stimulating the chest with weight because you keep on compensating for the lack of strength.
This is a common reason you may plateau. Let’s talk about sticking your chest out, does it actually help? Well sticking your chest out doesn’t actually help, in some cases, it could cause you to arch your back.
In a way it can be thought of as helpful but realistically just helps you to engage the chest properly, it won’t engage it any more than normal if you had a good mind to muscle connection and could fully engage it.
It could be helpful for starting off if you did not have that mind to muscle connection and had a hard time engaging the chest. Eventually, you would want to drop it because it could hold you back in the future by arching your back.
Now here is the interesting part, if you change angles to incline or decline it is important to maintain the same benching positioning as if you were to do it flat.
Especially with the elbows the reason why is because you can change the angles through moving your elbow position which is changing the angle your lifting from. What I mean is by flapping your arms out further from your body of keeping them closer in.
You want to keep it consistent, by changing the angle you change the focus of the weight and how your chest lifts, basically on the sagittal (vertical) plane you focus more weight to the upper or lower part of your chest.
This is good for aesthetics because you can have control over how you want your chest to develop by dipping it low with a decline angle or building some nice collar bone definition with the incline.
The reason why is because you are already changing the angle with the bench, by changing the angle with the arms too you can completely change the focus of weight on an incline or decline to be the complete opposite which means you could be working your chest from the same angle on your decline as incline, so keep it consistent with position.
That should hopefully paint a picture in your head of how you should be lifting on a bench press.
Now that you have the proper basics when you are then told modifications for specific benefits you can use that to your advantage, play with your bench a little to get those benefits. An example would be one of my common recommended ways of performing an exercise is constant tension keep the muscle engaged and ultimately cut the rest time which will help maximize growth.
What I mean by this is compromise the range of motion, shorten it to the part of the lifting where the muscle is fully engaged, at the beginning and end of the lift is usually when you can rest and is usually done for the last few reps there is a small rest in between for a little recovery.
We want to eliminate this and stay in the range of motion the muscle is 100% engaged. Be very tedious with this and start by lifting the weight from starting position and stop for a few seconds when you feel your chest fully engaged, remember that position and feeling and start raising until you feel your chest start to disengage, stop there for a few seconds.
It is in this range of motion you want to stay and lift in, by doing this you keep the muscle engaged, cut down rest time which does actually make a difference even though it is such a small difference.
You still maximize the most you can of the range of motion but you also stay in the range where most strength is used and built. As a beginner, you may want to use the full range of motion to loosen your joints and fire off all the muscle fibers.
When you do this you will feel how much harder and more intense it is to lift this way. You will also feel the strength increases so long as you provide enough rest time.
Must Read: Waist Training – Best Waist Working Out